19mm Poly Fittings

19mm Poly Clamp

Poly ratchet clamps should be used on all low-density poly fittings to ensure that the tube stays on the barbed fitting.   The 19mm poly clamp can be used on 19mm low density poly pipe and 19mm dripline.

19mm Poly Joiner

Used to join 19mm poly to 19mm poly and to make fast and secure repairs.   Make sure that you use a clamp or Cobra clip.

19mm End Plug

End plugs are used to close the end of a poly line.   All fittings including plugs must be secured to the poly using a clamp.

Reducing Joiner, 19mm to 13mm

This is just like the standard joiner except it has different sized ends.   One side takes the larger 19mm poly pipe and the other side takes the smaller 13mm.  

19mm Poly Elbow

Poly x poly elbow used for making 90 degree turns.

19mm x 1/2" male Elbow

Poly x 1/2" male elbow used to provide water to a pop-up spray or riser outlet.

19mm Poly Tee

Poly x poly x poly Tee.  

19mm x 1/2" male Tee

Poly x 1/2" male x poly tee used to provide water to a pop-up spray or a riser with a spray outlet on top.

19mm x 3/4" Director

Directors are used to connect low-density poly pipe onto solenoid valves and any other female BSP fitting.

CAPO Rubber Grommet 19mm ID x 19mm XPANDO fittings

The CAPO rubber grommet is used with XPANDO 19mm fittings to allow for the easy and secure attachment of 19mm or 25mm tube to polyethylene and PVC supply pipes for irrigation systems.   The 19mm ID CAPO suits the 22mm Antelco drill bit (code...

19mm x 1" Director

Directors are used to connect low-density poly pipe onto solenoid valves and any other female BSP fitting.

Reducing Tee 19mm x 13mm

The reducing tees are used where a branch line needs to be smaller than the main.

19mm x 3/4" male Elbow

Poly x 3/4" male elbow used to provide water to a pop-up spray or riser outlet.

XPANDO 19mm inlet x 19mm Take-Off

XPANDO 19mm fittings to allow for the easy and secure attachment of 19mm tube to polyethylene and PVC supply pipes for irrigation systems.   Requires a CAP 10145755 Grommet.

19mm x 3/4" male Tee

19mm Poly x 3/4" male x poly tee used to provide water to a pop-up spray, sprinkler or a riser with a spray outlet on top.

19mm x 1/2" Female Threaded Elbow

Poly x 1/2" female threaded elbows are used to install an articulated riser for a pop-up sprinkler/spray or, to install a 1/2" male riser so that a larger spray or sprinkler can be mounted well above the ground.

Pink Plumbers Teflon Tape - 10m roll

Our Pink Plumbers Tape is true tradesman quality thick heavy duty teflon tape and is recommended for all poly, plastic, brass and steel BSP fittings to provide a perfectly waterproof connection.   Do not use cheap imitations!   There...

XPANDO 19mm inlet x 25mm Take-Off

XPANDO 19mm fittings to allow for the easy and secure attachment of 25mm tube to polyethylene and PVC supply pipes for irrigation systems.   Requires a CAP 10145755 Grommet.

19mm x 1/2" Female Threaded Tee

Poly x 1/2" female threaded tees are used to install an articulated riser for a pop-up sprinkler/spray or, to install a 1/2" male riser so that a larger spray or sprinkler can be mounted well above the ground.

19mm Poly x Click-On Connection

This item connects 19mm low-density poly pipe directly to a standard Click-On tap connection.   Make sure that you use a 19mm stainless steel Cobra clip to hold the poly pipe.

19mm In-Line Filter

In-Line filters must be installed wherever micro sprays, drippers or micro sprinklers are to be used.   Ideally, you should install a 25mm plastic disk filter at the tap but the in-line filters will be fine if you have very clean town water.

19mm In-Line Tap

Our in-line taps are used in the low-density poly line to provide a manual isolation.   This is particularly usefull in greenhouses and fern hot houses.

Cobra Clips for 19mm poly pipe C21/8

Cobra Clips are full stainless steel clips used to provide a permanent and drip-proof connection for poly pipe to poly fittings, the Cobra C21/8 are used on 19mm black low density poly pipe and 19mm dripline.   Excellent value for money,...