Antelco

13mm End Plug

13mm end plugs are used to close the end of a poly line.   All fittings including plugs must be secured to the poly using a clamp.

13mm In-Line Filter

13mm In-Line filters must be installed wherever micro sprays, drippers or micro sprinklers are to be used.   Ideally, you should install a 25mm plastic disk filter at the tap but the...

13mm In-Line Tap

Our in-line taps are used in the low-density poly line to provide a manual isolation.   This is particularly usefull in greenhouses and fern hot houses.

13mm Poly Clamp

Poly ratchet clamps should be used on all low-density poly fittings to ensure that the tube stays on the barbed fitting.  This clamp is used on 13mm poly fittings for low density black poly pipe...

13mm Poly Elbow

13mm Poly x poly barbed elbow used for making 90 degree turns.

13mm Poly Joiner

13mm Low density poly x 13mm Low density poly barbed joiner, requires 2 x poly clamps or Cobra clips to make the connection secure.

13mm Poly Tee

13mm poly x poly x poly barbed Tee.  

13mm Poly x Click-On Connector

This item connects 13mm low-density poly pipe directly to a standard Click-On tap connection.   Make sure that you use a 13mm stainless steel Cobra clip to hold the poly pipe.

13mm x 1" Director

Directors are used to connect low-density poly pipe onto solenoid valves and any other female BSP fitting, you will need a clamp to hold the low density poly onto the director.   Directors...

13mm x 1/2" BSP Director (Hose Tail)

Directors are used to connect low-density poly pipe onto solenoid valves and any other female BSP fitting, you will need a clamp to hold the low density poly onto the director.   Directors...

13mm x 1/2" Female Threaded Elbow

Poly x 1/2" female threaded elbows are used to install an articulated riser for a pop-up sprinkler/spray or, to install a 1/2" male riser so that a larger spray or sprinkler can be mounted well...

13mm x 1/2" Female Threaded Tee

Poly x 1/2" female threaded tees are used to install an articulated riser for a pop-up sprinkler/spray or, to install a 1/2" male riser so that a larger spray or sprinkler can be mounted well above...

13mm x 1/2" male Elbow

Poly x 1/2" male elbow used to provide water to a pop-up spray or riser outlet.

13mm x 1/2" male Tee

Poly x 1/2" male x poly tee used to provide water to a pop-up spray or a riser with a spray outlet on top.

13mm x 3/4" Director

Directors are used to connect low-density poly pipe onto solenoid valves and any other female BSP fitting, you will need a clamp to hold the low density poly onto the director.   Directors...

19mm End Plug

End plugs are used to close the end of a poly line.   All fittings including plugs must be secured to the poly using a clamp.

19mm In-Line Filter

In-Line filters must be installed wherever micro sprays, drippers or micro sprinklers are to be used.   Ideally, you should install a 25mm plastic disk filter at the tap but the in-line...

19mm In-Line Tap

Our in-line taps are used in the low-density poly line to provide a manual isolation.   This is particularly usefull in greenhouses and fern hot houses.

19mm Poly Clamp

Poly ratchet clamps should be used on all low-density poly fittings to ensure that the tube stays on the barbed fitting.   The 19mm poly clamp can be used on 19mm low density poly pipe and...

19mm Poly Elbow

Poly x poly elbow used for making 90 degree turns.

19mm Poly Joiner

Used to join 19mm poly to 19mm poly and to make fast and secure repairs.   Make sure that you use a clamp or Cobra clip.

19mm Poly Tee

Poly x poly x poly Tee.  

19mm Poly x Click-On Connection

This item connects 19mm low-density poly pipe directly to a standard Click-On tap connection.   Make sure that you use a 19mm stainless steel Cobra clip to hold the poly pipe.

19mm x 1" Director

Directors are used to connect low-density poly pipe onto solenoid valves and any other female BSP fitting.

19mm x 1/2" Female Threaded Elbow

Poly x 1/2" female threaded elbows are used to install an articulated riser for a pop-up sprinkler/spray or, to install a 1/2" male riser so that a larger spray or sprinkler can be mounted well...

19mm x 1/2" Female Threaded Tee

Poly x 1/2" female threaded tees are used to install an articulated riser for a pop-up sprinkler/spray or, to install a 1/2" male riser so that a larger spray or sprinkler can be mounted well above...

19mm x 1/2" male Elbow

Poly x 1/2" male elbow used to provide water to a pop-up spray or riser outlet.

19mm x 1/2" male Tee

Poly x 1/2" male x poly tee used to provide water to a pop-up spray or a riser with a spray outlet on top.

19mm x 3/4" Director

Directors are used to connect low-density poly pipe onto solenoid valves and any other female BSP fitting.

19mm x 3/4" male Elbow

Poly x 3/4" male elbow used to provide water to a pop-up spray or riser outlet.

19mm x 3/4" male Tee

19mm Poly x 3/4" male x poly tee used to provide water to a pop-up spray, sprinkler or a riser with a spray outlet on top.

2 L/H Antelco CETA Pressure Compensated Dripper Bag of 200

The Antelco CETA pressure compensating dripper is made in Australia by Antelco, an Australian Owned company.   This is one of the most accurate drippers available and with...

2 L/H Antelco CETA Pressure Compensated Dripper Bag of 50

The Antelco CETA pressure compensating dripper is made in Australia by Antelco, an Australian Owned company.   This is one of the most accurate drippers available and with...

25mm End Plug

25mm End plugs are used to close the end of a poly line.   All fittings including plugs must be secured to the poly using a clamp.

25mm In-Line tap

Our in-line taps are used in the low-density poly line to provide a manual isolation.   This is particularly usefull in greenhouses and fern hot houses as well as any other irrigation...

25mm Poly Clamp

Poly ratchet clamps should be used on all low-density poly fittings to ensure that the tube stays on the barbed fitting.   This clamp can be used on all 25mm low density black poly pipe.

25mm Poly Elbow

25mm barbed poly elbows are used to make a 90 degree turn in the poly pipe and so prvent any kinking, make sure that you use clamps with this fitting.

25mm Poly Joiner

25mm barbed joiners are used to join a further length of 25mm poly to an existing length as well as making repairs easier and faster.   Remember to use clamps with these fittings to prevent...

25mm Poly Tee

25mm poly tees are used to provide an off-take for another 25mm poly line, make sure that you use clamps with these fittings.

25mm x 1" BSP Director

Directors are used to connect 25mm low-density poly pipe onto 1" female BSP solenoid valves and any other female BSP fitting.

25mm x 1/2" Female Threaded Elbow

25mm poly x 1/2" female BSP elbow used to provide water to a pop-up spray, sprinkler or a riser with a spray outlet on top.

25mm x 1/2" Female Threaded Tee

25mm poly x 1/2" female BSP tee used to provide water to a pop-up spray, sprinkler or a riser with a spray outlet on top.

25mm x 1/2" male Elbow

25mm poly x 1/2" male BSP elbow used to provide water to a pop-up spray, sprinkler or a riser with a spray outlet on top.

25mm x 1/2" male Tee

25mm poly x 1/2" male BSP tee used to provide water to a pop-up spray, sprinkler or a riser with a spray outlet on top.

25mm x 3/4" BSP Director

Directors are used to connect 25mm low-density poly pipe onto 3/4" female BSP solenoid valves and any other female BSP fitting.

25mm x 3/4" male Elbow

25mm poly x 3/4" male BSP elbow used to provide water to a pop-up spray, sprinkler or a riser with a spray outlet on top.

25mm x 3/4" male Tee

25mm poly x 3/4" male BSP tee used to provide water to a pop-up spray, sprinkler or a riser with a spray outlet on top.

4 L/H Antelco CETA Pressure Compensated Dripper Bag of 200

The Antelco CETA pressure compensating dripper is made in Australia by Antelco, an Australian Owned company.   This is one of the most accurate drippers available and with...

4 L/H Antelco CETA Pressure Compensated Dripper Bag of 50

4 L/H Antelco CETA Pressure Compensated Dripper Bag of 50The Antelco CETA pressure compensating dripper is made in Australia by Antelco, an Australian Owned company.   This is one...

4.5mm Barbed Connector

These joiners are barbed on both ends and are used to join our 4mm flexible tubing.

4.5mm Barbed Connector - Bag of 100

Used to connect 4 flexible tube to the 13/19/25mm low-density poly supply line.   Also used to connect 3/5 flexible tube to 3/5 flexible tube.   This is the bulk 100 pieces...

4.5mm Tee - All barbed ends

Used to connect 4mm flexible tube in a "T" configuration.